Woodworking machinery supplier in China: After 20 years development, V-HOLD has constructed strong hardware facilities and humanized management system by bringing in tens of brand-new large automotive precision CNC machine center from developed countries such as Japan, German, along with over 67,000m2 large modern workshop with complete facilities and production lines, V-HOLD has realized its high efficient production. Besides that, the cooperation with world famous management consulting firm and introduction of modern business administration system such as ERP, 6S have laid solid foundation to the development of V-HOLD. Thanks for the trust and support of our customer. V-HOLD will consistently stick to the belief that: Profession and concentration accomplish excellent brand ! Discover more info at woodworking machines manufacturer.
The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.
A typical hydraulic down-acting press uses a pair of hydraulic cylinders, one on each end, to generate the tonnage required for the down stroke of the machine. Traditionally, these machines have a C or O frame profile design. With both types, when facing the front of the machine the hydraulic cylinders are located on the left and right hand side of the upper beam. Since the upper beam is being pushed down and up with hydraulic power, the upper beam will fall during a power outage and could create an unsafe environment. Down acting presses are commonly blocked at night to take pressure off of the hydraulic system. The lower beam does not move during bending so the operator will not get feedback that the brake is engaged.
Sanding is the operation of finishing wooden items after they have been machined. Essentially, a sanding machine performs a sand papering job to produce a uniformly sanded surface. Three common types of sanding machines are : Belt sander; Spindle sander; Disc sander. It has an endless cloth backed abrasive belt which runs over two drums and is used for sanding and shaping flat surfaces. One of the drums is rotated by an electric motor and serves as the driver, while the other supports the belt and keeps it in proper tension. For sanding work by the abrasive belt, the the workpiece is supported by an adjustable table that may be tilted to any desired angle.
The most common application involves gluing a coating (veneer, laminate, composite, PVC etc) onto a substratum (MDF, hardboard, plywood, hollow panels, blockwood etc). The basic configuration of the pressing line is comprised of a feed belt, an automatic press and a discharge deck. This configuration can be completed with numerous options, such as glue spreaders, polishers, automatic feeders, disk, roller or belt conveyors, automatic assembling stations, panel turners and stackers. Lines with various degrees of automation can be supplied right up to fully automatic lines that do not require direct intervention by the operator.
The woodworking lathe is one of the most important machines used in a carpentry shop. This is employed primarily for turning jobs in making cylindrical parts. However, by suitably manipulating the tools, tapers, radii, and other irregular shapes can also be easily turned. It resembles the engine lathe most frequently used in the machine shop, and consists of a cast iron bed, a head stock, tail stock, tool rest, live and dead centers, and a speed control device (Fig. 10.54). The drive, in modern lathes, is individual motor driven ; and a cone pully on the head stock spindle is connected by a belt to a cone pully on the motor shaft.
Modern machinery often requires pneumatic pressure, be it for saws, sanders, impact wrenches, grinders, spray guns, washers, stapling, nailing or pneumatic tooling, the compressor has become a necessity. The compressor consists of: motorised pump; tank for storing the compressed air; on/off control; regulator. There’s also a metal frame on which all the parts are mounted, usually with a carrying handle and occasionally wheels. A drill press can be used to drill round holes, sanding, grooving and mortising with the addition of specialised attachments. Read additional information at https://www.v-holdmachinery.com/.